Beta version — entries are being reviewed and expanded. Corrections are welcome at hello@vanvino.store.
GuideFabric specFor buyers

How to Read a Fabric Specification

Decode a line like 200TC — 110×90 — 40s/40s, and spot a misleading spec
A woven-fabric specification compresses a fabric's construction into a short code: thread count, warp × weft density and warp/weft yarn counts. Learning to read it — for example 200TC — 110×90 — 40s/40s — lets a buyer understand and compare fabrics objectively, verify a thread-count claim, and recognize the tricks used to make a spec look better than the cloth.

To a professional buyer, a fabric spec is more trustworthy than a marketing thread-count figure, because it reveals the construction behind the headline. Once you can read each element and see how they relate, you can judge a fabric and catch an inflated claim at a glance.

This guide decodes a worked example, shows how the numbers must add up, compares common thread-count tiers, and lists the warning signs of a misleading specification.

Worked example

Decoding 200TC — 110 × 90 — 40s/40s

A typical woven spec has three parts: the thread count, the warp × weft density, and the warp/weft yarn counts. Here is each element of 200TC — 110 × 90 — 40s/40s:

01200TC — 200 threads per square inch, by the conventional warp + weft count.
02110 — 110 warp threads (ends) per inch — the lengthwise density.
0390 — 90 weft threads (picks) per inch — the crosswise density.
0440s (warp) — the warp yarn is English cotton count Ne 40 — a fine-ish, good-quality single yarn.
0540s (weft) — the weft yarn is also Ne 40 — a balanced construction with the same yarn both ways.
The check

The numbers must add up

A genuine spec is internally consistent: the warp and weft densities must sum to the stated thread count. In the example, 110 + 90 = 200, so the 200TC claim is consistent with the stated construction. If a spec claims a thread count that its warp × weft figures cannot produce, the number has been inflated.

Warp and weft density can be determined by standardized methods such as ASTM D3775, so these are verifiable, not marketing. Asking for the full warp × weft × yarn-count breakdown — not just the TC headline — is the single best way to verify a fabric.

Comparing tiers

144TC, 200TC, 300TC, 600TC — what changes

Within genuine single-ply cotton, higher thread count means denser, smoother, more substantial, more opaque fabric — up to the practical limit of fine cotton (roughly 400, though very fine yarns can push higher). The common tiers compare roughly like this: 144TC is a basic, lighter, more economical sheeting; 200TC is a solid everyday-to-good quality; 300TC is a fine, smooth, denser quality; and genuine 600TC requires very fine yarn or (more often) counts plies to reach the number.

So 144 vs 200 and 200 vs 300 are real steps up in density and hand when the yarn is genuine single-ply. But 300 vs 600 is where claims usually break down: a real 600 single-thread count in fine cotton is rare, so a '600TC' sheet is frequently a 300-count two-ply fabric with each ply counted, which is not twice the fabric.

Warning signs

Spotting a misleading specification

Most thread-count inflation comes down to a few tricks. The clearest is ply counting: a two-ply yarn woven at 250 ends + 250 picks (500 single threads) is honestly 500TC, but some label it 1000TC by counting both plies. The spec tell-tale is a plied yarn (e.g. 80/2) behind an improbably high count. Other signs are a very high TC with a coarse yarn count (the yarn is too thick to pack that densely), a TC that exceeds the physical limit for the fiber, or a headline TC with no warp × weft × yarn breakdown offered.

01Single vs plied yarn — a single-thread count (from /1 yarns) is the honest figure. If the yarn is plied (/2, /3) and each ply is counted, the TC is inflated — ask for the single-thread count.
02TC above the fiber's limit — in genuine single-ply cotton the count rarely exceeds ~400 threads per inch (very fine yarns can go somewhat higher). A '1000TC' pure-cotton sheet is almost always ply-counted or using non-cotton/inflated yarns.
03Coarse yarn, high TC — you cannot pack a coarse yarn (low Ne) to a very high density. A high TC paired with a low yarn count is physically inconsistent.
04No full breakdown — a trustworthy supplier can give warp × weft × yarn counts. A TC headline with no breakdown is a red flag.

Frequently asked questions

What does 200TC — 110×90 — 40s/40s mean?+
200 threads per square inch, made of 110 warp threads and 90 weft threads per inch, using Ne 40 single yarn in both warp and weft. The density figures add up to the thread count (110 + 90 = 200), confirming the claim is internally consistent; only a thread-count test on the cloth (for example ASTM D3775) verifies the densities themselves.
Is a 600 thread count sheet twice as good as 300?+
Usually not. A genuine 600 single-thread count in fine cotton is rare; a '600TC' sheet is most often a 300-count two-ply fabric with each ply counted. It is not twice the fabric, and may even be heavier and less breathable. Check whether the yarn is single or plied.
How can I verify a thread-count claim?+
Ask for the full construction: warp × weft density and the warp/weft yarn counts. The warp and weft densities must add up to the stated thread count, and these can be measured by standards like ASTM D3775. If a supplier won't give the breakdown, treat the headline number with caution.

Sourcing certified textiles?

Vanvino® can source and document certified textiles and advise on the right standard for your market and project.

Request advice
Last updated · Published by Vanvino® · Editorial policy & corrections