GuideWeavingWarp · weft · loom
Understanding Weaving: Warp, Weft & the Loom
How a woven fabric is built — the two thread systems and the loom that interlaces them
Weaving builds fabric by interlacing two sets of yarns at right angles: the warp, which runs lengthwise and is held under tension on the loom, and the weft (or filling), which is inserted across the warp row by row. The loom raises and lowers selected warp yarns to create a gap (the shed) through which the weft passes, and the pattern of raising and lowering defines the weave structure.
Almost every flat, non-stretchy fabric in bedding, table and many apparel textiles is woven. Understanding the two thread systems and how the loom interlaces them is the foundation for reading any woven-fabric specification — the warp and weft counts, the density, and the weave structure all follow from this process.
This guide walks through the elements of weaving and the sequence a loom repeats thousands of times a minute to build cloth.
Start here
Plain WeaveThe firmest basic weave — behind percale and poplin.
The two thread systems
Warp and weft
A woven fabric is a grid of two thread systems. Getting them straight is essential to reading any spec:
01Warp (ends) — the lengthwise yarns, running the length of the roll, held under tension on the loom. Warp yarns must be strong and are often sized (coated) to survive weaving. In a spec, the warp count and warp density come first.
02Weft / filling (picks) — the crosswise yarns, inserted across the warp one row at a time. Each insertion is a 'pick'. Weft yarns carry less tension and can be softer or fancier. In a spec, the weft count and weft density (picks) come second.
03Selvedge — the finished, self-bound edges running down both sides of the fabric where the weft turns back, which stop the fabric fraying along its length.
The loom sequence
How the loom makes cloth
The loom repeats a short cycle to interlace the threads:
01Warp preparation — thousands of warp yarns are wound in parallel onto a beam at even tension, threaded through the loom, and usually sized for strength. Good warp preparation is critical to weaving without breaks.
02Shedding — the loom raises some warp yarns and lowers others to open a triangular gap called the shed. Which yarns lift on each pick is what creates the weave structure (plain, twill, satin…).
03Weft insertion (picking) — a weft yarn is carried across through the open shed — by a shuttle, rapier, air-jet or water-jet, depending on the loom.
04Beat-up — a comb-like reed pushes the newly inserted weft firmly against the already-woven cloth, setting the weft density (picks per inch).
05Take-up & let-off — the woven cloth is wound on and fresh warp released, keeping tension constant, and the cycle repeats.
Frequently asked questions
What is the difference between warp and weft?+
The warp runs lengthwise along the fabric and is held under tension on the loom; the weft (filling) is inserted crosswise, row by row, through the warp. Warp yarns must be stronger; weft yarns can be softer. In specifications, warp figures are given before weft.
What is the 'shed' in weaving?+
The shed is the temporary gap the loom opens by raising some warp yarns and lowering others, so the weft can pass through. The pattern of which warp yarns lift on each row is what creates the weave structure — plain,
twill or satin.
Why does the warp need to be stronger than the weft?+
The warp is held under continuous tension and rubbed by the loom's moving parts throughout weaving, so it must resist breaking and is often sized (coated) for strength. The weft experiences far less stress, so it can be a softer or fancier yarn.
Sourcing certified textiles?
Vanvino® can source and document certified textiles and advise on the right standard for your market and project.
Request advice