Beta version — entries are being reviewed and expanded. Corrections are welcome at hello@vanvino.store.
DurabilityTested propertyAbrasionASTM D4157

Wyzenbeek Abrasion

The US 'double rub' abrasion test for upholstery durability
Abrasion resistance
The Wyzenbeek abrasion test rates a fabric's resistance to wear by rubbing it back and forth in a straight line against a standard abradant under tension, counting 'double rubs' to failure. It is the dominant abrasion standard in North America for upholstery, the counterpart to Europe's Martindale test, and is reported as a double-rub count.

In the test (ASTM D4157), a taut specimen is rubbed in a straight back-and-forth motion against a standardized abradant (cotton duck or wire mesh) under a set tension and load; one back-and-forth pass is a 'double rub', and the count continues to a defined failure point such as yarn breakage.

Wyzenbeek counts map to the ACT voluntary guidelines for US upholstery: 15,000 double rubs for general contract (low-traffic) and 30,000 for heavy-duty (high-traffic) use. Some very demanding installations specify more, but ACT notes that results above 100,000 double rubs have not been shown to indicate a longer service life. Because the motion is unidirectional (unlike Martindale's figure-of-eight), results depend on which direction is tested, and Wyzenbeek double rubs cannot be reliably converted to Martindale rubs. Buyers working across US and European supply chains must know which standard a figure refers to.

At a glance

PropertyAbrasion resistance
Measured inDouble rubs to failure
MotionStraight back-and-forth under tension
Key standardASTM D4157
Applies toUpholstery, contract textiles
RegionNorth America (primary)

Characteristics

01Rubs fabric back and forth in a straight line
02Counts 'double rubs' to a failure point
03Specimen held under tension
04Dominant abrasion standard in North America
05Unidirectional (direction-dependent) wear

Typical uses

01US upholstery and contract specifications
02Hospitality and commercial seating
03Durability acceptance testing
04Rating fabrics into US use tiers
05Cross-checking against Martindale projects

Strengths

01Objective, recognized US durability figure
02Clear tiers for specifying upholstery
03Standardized (ASTM D4157)
04Familiar to North American buyers
05Comparable across suppliers when method stated

Limitations

01Unidirectional — direction affects the result
02Not convertible to Martindale rubs
03Very high counts add little real-world meaning
04Abradant and tension affect the figure
05Standard and target must be stated

Where it applies

Wyzenbeek is the abrasion specification North American buyers use to rate upholstery durability — general contract, heavy-duty or high-traffic commercial — the US counterpart to Martindale. Because it rubs in a straight line, the result depends on direction, and its double-rub counts cannot be converted to Martindale rubs. For projects spanning US and European supply chains, state clearly which standard (ASTM D4157 or ISO 12947) a durability figure refers to, so tiers are not misread.

HospitalityContractHome fashionFashion

Frequently asked questions

What is a 'double rub'?+
One complete back-and-forth pass of the abradant over the fabric in the Wyzenbeek test. The count of double rubs to failure is the fabric's Wyzenbeek abrasion rating — for example 30,000 double rubs for heavy-duty upholstery.
Can Wyzenbeek double rubs be converted to Martindale rubs?+
No, not reliably. The two tests use different motions (straight back-and-forth vs figure-of-eight), abradants and end points, so there is no trustworthy conversion. A fabric should be specified and tested to one standard, and the standard stated.
How many double rubs are needed for commercial use?+
Under the ACT voluntary guidelines: 15,000 double rubs for general contract and 30,000 for heavy-duty, high-traffic upholstery. Results above 100,000 double rubs have not been shown to indicate a longer service life, so the tier matters more than chasing the biggest number.

Sourcing with wyzenbeek abrasion?

Vanvino® can source, specify and document textiles to your exact construction and quality requirements.

Request advice
Last updated · Published by Vanvino® · Editorial policy & corrections