Beta version — entries are being reviewed and expanded. Corrections are welcome at hello@vanvino.store.
StrengthTested propertyWarp & weftISO / ASTM

Tensile Strength

How much pulling force a fabric withstands before it breaks
Tensile (breaking) strength
Tensile strength is the maximum pulling (tensile) force a fabric can take before it breaks, measured separately in the warp and weft directions. It is a core specification for woven fabrics, tested by clamping a strip in a tensile tester and pulling until rupture, with the result reported as a force (newtons or pounds-force) and often the elongation at break.

Two standard approaches exist. The strip method (ISO 13934-1, the constant-rate-of-extension 'strip test') grips the full width of a cut strip and records the maximum force and elongation. The grab method (ISO 13934-2 / ASTM D5034) grips only the center of a wider specimen, giving a quicker, more application-realistic figure. Results are always reported per direction, because warp and weft usually differ.

Tensile strength tells a buyer whether a fabric will survive the stresses of its use — bedding pulled taut, upholstery under tension, bags and workwear under load. It is governed by fiber strength, yarn count and twist, and thread density. It is distinct from tear and bursting strength, which measure different failure modes, so a full specification usually calls out several.

At a glance

PropertyTensile (breaking) strength
Measured inNewtons (N) or pounds-force (lbf)
DirectionsWarp and weft, reported separately
Key standardsISO 13934-1/-2, ASTM D5034 (grab), D5035 (strip)
Applies toWoven fabrics
Also reportsElongation at break (%)

Characteristics

01Maximum force a fabric takes before breaking
02Measured independently in warp and weft
03Strip method (full width) or grab method (center)
04Reported as force, often with elongation at break
05Driven by fiber, yarn count/twist and density

Typical uses

01Specifying bedding, upholstery and covers
02Workwear, bags and technical textiles
03Comparing woven qualities on a like-for-like basis
04Quality control against a target value
05Supporting durability claims

Strengths

01Objective, comparable number
02Directly relevant to in-use stresses
03Standardized and widely recognized
04Reveals warp/weft imbalance
05Pairs with elongation for a fuller picture

Limitations

01Mainly used for wovens and nonwovens (stretchy knits are usually tested for bursting strength)
02Strip vs grab figures are not interchangeable
03Doesn't capture tear or abrasion behavior
04A single value hides direction differences
05Needs the test method stated to be meaningful

Where it applies

Tensile strength is a foundational line in any serious woven-fabric specification — it tells you whether bedding, upholstery, covers, workwear or technical textiles will survive their in-use loads. Because warp and weft differ and because the strip and grab methods give different figures, a spec must state the method (ISO 13934 or ASTM D5034/D5035) and both directions. It is one of several strength measures: pair it with tear and, for knits, bursting strength.

Home fashionHospitalityContractFashion

Frequently asked questions

What is the difference between the strip and grab tensile tests?+
The strip test (ISO 13934-1) grips the full width of a cut strip; the grab test (ISO 13934-2 / ASTM D5034) grips only the center of a wider specimen. The grab test is quicker and more like real-use loading, but its numbers are higher and not interchangeable with strip results, so the method must be stated.
Why is tensile strength reported for warp and weft separately?+
A woven fabric's warp and weft usually have different yarns, counts and densities, so they break at different forces. Reporting both directions prevents a fabric that is strong one way and weak the other from looking acceptable on a single number.
Is tensile strength the same as tear strength?+
No. Tensile strength measures the force to break the fabric pulled end-to-end; tear strength measures the force to propagate an existing tear. A fabric can be strong in tension but tear easily, so both are specified for demanding uses.

Sourcing with tensile strength?

Vanvino® can source, specify and document textiles to your exact construction and quality requirements.

Request advice
Last updated · Published by Vanvino® · Editorial policy & corrections