StrengthTested propertyKnits & nonwovensISO / ASTM
Bursting Strength
The multidirectional strength test for knits and nonwovens
Bursting strength
Bursting strength is the pressure a fabric withstands before it ruptures when pushed out from behind over a fixed area — a multidirectional strength test used where a simple warp/weft tensile test does not apply. It is the standard strength measure for knitted fabrics, nonwovens, lace and other constructions that stretch and load in all directions at once.
In the test (ISO 13938 / ASTM D3786), the fabric is clamped over a circular opening and a rubber diaphragm (hydraulic or pneumatic) is inflated beneath it until the fabric bursts; the pressure at rupture is the bursting strength, reported in kilopascals (kPa) or psi. Because the force is applied in every direction simultaneously, it suits fabrics with no single dominant yarn direction.
Knits are the main case: a jersey or rib fabric stretches and bears load omnidirectionally, so a warp/weft tensile figure would be misleading. Bursting strength also applies to nonwovens, lace and medical textiles. It is driven by yarn strength, stitch density and structure, and is specified for knitwear, knitted bedding, activewear and single-use nonwoven products.
At a glance
PropertyBursting strength
Measured inKilopascals (kPa) or psi
MethodDiaphragm (hydraulic or pneumatic)
Key standardsISO 13938-1/-2, ASTM D3786
Applies toKnits, nonwovens, lace
DirectionMultidirectional (all at once)
Characteristics
01Pressure to rupture a fabric from behind
02Applies force in all directions at once
03Diaphragm inflated until the fabric bursts
04Standard strength test for knits and nonwovens
05Driven by yarn strength and stitch density
Typical uses
01Knitwear and knitted bedding
02Activewear and stretch fabrics
03Nonwovens and single-use textiles
04Lace and open constructions
05Quality control against a target pressure
Strengths
01Right test for multidirectional fabrics
02Objective, comparable figure
03Standardized across ISO and ASTM
04Suits knits where tensile is misleading
05Covers nonwovens and lace too
Limitations
01Rarely specified for conventional wovens, where tensile strength is the usual measure
02Single value, no direction breakdown
03Hydraulic and pneumatic results can differ
04Area of the test head affects the figure
05Method must be stated to compare
Where it applies
Bursting strength is the correct strength specification for knits, nonwovens and lace — fabrics that stretch and load in every direction, where a warp/weft tensile figure would mislead. It underpins knitwear, knitted bedding, activewear and single-use nonwoven products. Specify it (ISO 13938 / ASTM D3786) with the method and test-head area stated; for conventional wovens, use tensile and tear strength instead.
Home fashionHospitalityFashionContract
Frequently asked questions
When is bursting strength used instead of tensile strength?+
For fabrics with no single dominant yarn direction — knits, nonwovens, lace — which stretch and load in all directions. A warp/weft tensile test suits wovens; bursting strength applies multidirectional pressure, matching how these fabrics actually bear load.
How is bursting strength measured?+
The fabric is clamped over a circular opening and a rubber diaphragm is inflated beneath it (hydraulically or pneumatically) until the fabric ruptures. The pressure at rupture, in kPa or psi, is the bursting strength (ISO 13938 / ASTM D3786).
Does bursting strength give warp and weft values?+
No. Because the force is applied in all directions at once, it produces a single figure rather than separate warp and weft values — which is exactly why it suits knits and nonwovens.
Sourcing with bursting strength?
Vanvino® can source, specify and document textiles to your exact construction and quality requirements.
Request advice